Laundry room cabinets in Clovis, planned around the machines
Laundry room cabinets in Clovis usually start with the same complaint: there is a washer, a dryer, one wire shelf, and nowhere to put anything down. Laundry is one of the few rooms where a relatively small cabinetry investment changes daily function immediately, because the room is currently doing one job when it could comfortably do four: washing, folding, hanging, and storing.
What a planned laundry run typically includes:
- Upper cabinets over the machines for detergent, supplies, and household overflow
- A folding counter, either spanning front loaders or as a dedicated run beside top loaders
- A hanging rod or pullout valet for items that come straight out of the dryer
- A tall utility cabinet for brooms, vacuum, ironing board, and mop
- A drying rack, either pullout or wall mounted
- Hamper pullouts for sorting
- A base cabinet with a utility sink where plumbing allows
The measurement that matters most is the machine itself. Washer and dryer dimensions vary significantly by model, and front loaders on pedestals change the height calculation entirely. We work from your actual model numbers rather than from a nominal 27 by 39 inch assumption, and if you are planning to replace the machines within a few years we design to the future machine.
Common laundry room problems
- No folding surface, so laundry migrates to a bed or the dining table
- A single wire shelf above the machines that is too high to reach and too shallow to hold much
- Detergent and supplies stored on top of the machines, where vibration eventually knocks them off
- No hanging space, so shirts wrinkle before they get hung elsewhere
- Gaps beside and between machines that collect lint and lost socks
- A vacuum and ironing board with no home, living in a hallway closet instead
Our process
Measure the room and the machines
We take machine model numbers, hookup locations, vent position, and door swings. Door swing conflicts are the most common design mistake in this room.
Layout
Uppers, counter, tall storage, and hanging placed around fixed constraints including the dryer vent and the water hookups.
Finish selection
Chosen for a room that will see water, heat, and detergent.
Build and install
Usually a one day installation for a standard laundry run.
Layout options
| Machine setup | What works | Watch for |
|---|---|---|
| Side by side front loaders | Counter spanning both machines, uppers above | Counter must clear the doors fully when open. Pedestals raise everything by 12 to 15 inches |
| Side by side top loaders | Uppers above, separate folding counter on an adjacent wall | Uppers must be high enough to clear a fully raised lid |
| Stacked units | Tall storage and counter beside the stack | Stacking frees a full machine width, usually the single biggest gain in a small laundry room |
| Laundry closet | Uppers only, plus a pullout or fold down surface | Bifold door clearance limits cabinet depth. Ventilation matters in an enclosed space |
| Garage laundry | Utility grade cabinets, sealed | Very common locally. Specify for garage temperature swings, same as garage cabinets |
Pricing factors
- Run length and how many walls are involved
- Counter material and span
- Utility sink and whether plumbing has to be extended
- Tall storage versus uppers only
- Pullout accessories such as hampers, drying racks, and valet rods
- Finish level, from utility to fully matched to the adjacent living space
Laundry cabinetry and the Clovis climate
Two local realities shape this room. The first is that a large share of Clovis laundry setups live in the garage rather than in a conditioned interior room, which is common across Central Valley housing of every era. A garage laundry has to be specified like garage cabinetry, meaning moisture resistant substrate, no thermofoil, and mechanical fasteners, because that cabinetry sees sustained summer heat and then weeks of high humidity during winter tule fog season. The second is water hardness. Groundwater across the Fresno and Clovis area carries heavy dissolved mineral content, which is why laundry rooms here so often include a softener, and why splash on cabinet faces leaves visible mineral deposits rather than drying clean. We seal all six sides of doors and drawer fronts in laundry rooms for the same reason we do it in bathrooms, and we specify catalyzed finishes on any surface near a utility sink. If a water softener is present or planned, tell us at the measure, because softener tanks are bulky and are far easier to design around than to work around afterward.
Financing available on cabinetry projects
Most kitchen cabinetry projects land between $8,000 and $40,000. We work with homeowners who would rather spread that over monthly payments than pay in full up front. Ask your estimator to walk you through the options during your free consultation.